Hydrotechnik MultiSystem 4070 Скачать руководство пользователя страница 54

Страница: 54 / 153

Firmware Version 2.0

MultiSystem 4070

Operating software

ENG

Presentation

The data of the selected measurement series can be presented in four diffe-
rent ways:

•

Table

: Presentation of all measured values of each channel in a table

•

Statistics

: Presentation of the minimum, maximum and average values of

each channel

•

Graph

: two different graphic presentations

– Time-dependent presentation
– Variable-dependent presentation

The graphics represent examples of the different types of presentations:

Information about the different display options can be found in the chapters:



Chapter

Presentation type “Table”

on page 60



Chapter

Presentation type “Graph”

on page 61

Channel on x axis

If you have selected the

GRAPH y=f (x)

presentation mode, you can select the

channel for the y axis. The first channel of the measurement is preset.

Table

Statistics

Graph

Содержание MultiSystem 4070


























































































































































Результаты поиска

Содержание MultiSystem 4070

Отзывы:

Hydrotechnik MultiSystem 4070, Руководство по эксплуатации, Страница: 54 / 153

Результаты поиска

Содержание MultiSystem 4070

Отзывы: