Hydrotechnik MultiSystem 4070 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 153

Hydrotechnik MultiSystem 4070 Скачать руководство пользователя страница 36

Firmware Version 2.0

MultiSystem 4070

36

Operation

ENG

Connect a PC and transfer data

1

Switch on measuring instrument and PC.

2

Make sure that “Mass storage device” is selected as USB mode and that
at least one volume is enabled.



See

USB (DEVICE)

3

Plug the supplied USB cable into the connector on the side of the measu-
ring instrument.

4

Plug the USB cable into an available USB jack on your PC.

System requirements for your PC:

• Windows 7/8 (driver required)



www.hydrotechnik.com

• Windows 8.1 or later

5

Wait until the measuring instrument has been detected by the PC.

6

Perform the data transfer as described in the software documentation.



The internal memory has two partitions:

•

DATA-VOL

This is the general memory for files (measurement series, images, etc.)

•

DOCU volume

This is where you will find the operating instructions, data sheets and soft-
ware for this instrument.

You have to install the

HYDRO

com

software on your PC before you can transfer

measurement data to your PC.

Data transfer with micro USB cable

The measuring instrument is recognized as a removable storage device. You can
therefore open the operating instructions directly from the instrument.
If the measuring instrument is not recognized, this may be due to the USB cable
you are using. Use a micro USB Type B cable that supports the “data transfer”
function.

«
...
34
35
36
37
38
...
»

Содержание MultiSystem 4070


























































































































































Отзывы:

Нет отзывов