Hydrotechnik MultiSystem 4070 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 153

Hydrotechnik MultiSystem 4070 Скачать руководство пользователя страница 10

Firmware Version 2.0

MultiSystem 4070

10

Description of the measuring instru-

ENG

Description of the measuring
instrument

Properties of the MultiSystem 4070

MultiSystem 4070

is a practice-oriented, user-friendly hand-held measuring

instrument that supports the user in the daily measuring functions. When using
sensors with ISDS (intelligent sensor detection), the

MultiSystem 4070

auto-

matically identifies the connected sensors during switch-on and adopts all
parameters: Measurement range, physical measurand, unit of measurement,
signal output and characteristic curve (linearization). You can also connect
sensors without ISDS designation. The entry of the sensor parameters is then
done in clear operation menus.

You can connect up to five sensors and store all measured values. Calculati-
ons from the measured values such as difference, sum and performance, as
well as the 1st derivation (e.g. speed from path) are available as additional
special channels for display and recording. The buffering of extreme values of
the minimum and maximum measurands is always active and can be display-
ed by the corresponding key selection.

All measurements can be conveniently transferred to a PC using a USB cable.
The

HYDRO

com

software is delivered for free with the instrument and offers

comprehensive support with functions for the evaluation, presentation and
printing of the measured values.

System requirements for your PC:

•

Windows 7/8 (driver required)



www.hydrotechnik.com

•

Windows 8.1 or later

«
...
8
9
10
11
12
...
»

Содержание MultiSystem 4070


























































































































































Отзывы:

Нет отзывов