HYDROSCAND AutoCut 5-32CTS Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 64

background image

Page 41

autocut 5-32cts user manual edItIon II 2015-01-16

6. Maintenance

the following instruction is to be performed by authorized personell only, which has got
access to the service key, see picture below.

• Set 3-way reset switch to ”0” and turn OFF the main switch, see chapter 5.4.1 pos 1.
• Wait until motor has stopped and open the blade cover hatch on the right side.
• Loosen the two stop screws ”1” by using a 3mm hexagon wrench.
• Loosen the centre screw ”2” by using a 10mm hexagon wrench. Note! left hand

thread!

• Take away the outer carrier plate.
• The cutting blade is now loose. Dismantle the old blade and clean all parts.

replace all parts with damages.

• Assemble a new one. Note! check the direction arrows on the blade.
• Assemble the outer carrier and centre bolt with a moment of torsion 80 Nm.
• Tighten the two stop screws back against the motor shaft end.
• Close the hatch on the right side.
• Start the cutting machine and check that no vibrations occure.

Caution!

*always use protective gloves when changing the cutting blade.
Important !

HYDROSCAND MACHINE AB

Kungsvägen 22

Phone: +46 (0)225 - 573 30

S-783 35 Säter

Fax:

+46 (0)225 - 501 08

Sweden

Web:

www.hydroscand-machine.se

Edition 7-00

MANUAL-E

Page 31

8. Maintenance

8.1 Replacement of cutting blade

• Set 3-way reset switch to "0" and turn

OFF

the

main switch

.

• Open the blade cover hatch on the right side.

• Loosen the two stop screws "

1

" by using a 3 mm hexagon wrench.

• Loosen the centre screw "

2

" by using a 10 mm hexagon wrench. Note! left hand

thread!

• Take away the outer carrier plate.

• The cutting blade is now loose. Dismantle the old blade and clean all parts.

Replace all parts with damages.

* Caution! Risk for cut injury ! Use protective gloves.

• Assemble a new one. Note! check the direction arrows on the blade.

• Assemble the outer carrier and centre bolt with a moment of torsion 80 Nm.

• Tighten the two stop screws back against the motor shaft end.

• Close the hatch on the right side.

Warning !

Always use protective gloves when changing the cutting blade.

Important !

Start the cutting machine and check that no vibrations occure.

1

2

«
...
39
40
41
42
43
...
»

Содержание AutoCut 5-32CTS

































































Отзывы:

Нет отзывов

Похожие инструкции для AutoCut 5-32CTS

Бренд: York Fitness Страницы: 34

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Hammer Страницы: 42

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Hällde Страницы: 40

Бренд: Hällde Страницы: 6

Бренд: Nabtesco Страницы: 26

Бренд: Samson Страницы: 2

Бренд: Kärcher Страницы: 148

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Бренд: ProLights Страницы: 28

Бренд: York International Страницы: 16

Бренд: X-10 Страницы: 12

Бренд: Equinox Systems Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды