Page 35
autocut 5-32cts user manual edItIon II 2015-01-16
5.7.3 I/o Control Input - output
this menus are for monitoring only and can be used for troubleshooting of plc I/o signals.
0 = signal is off, 1= signal is on.
1. Prev:
return to previousmenu.
2. Home:
Return to ”Main”menu.
5.7.4 Timmers / Counters
.
this menu is for setting energy saving parameters and ser-
vice intervals.
1. delay time cut:
set the wanted idling time for the cut
motor when cut sequence not is running.
2. delay time conveyor:
lengthen the conveyor feeding
time. Value ”0” = start and stopp is the same as for the belt
unit in cutting machine.
3. Counter blade:
actual cut quantity on cutting blade
(total from service) and set quantity before service (ser-
vice Interval*)
4. Counter Knife:
actual cut quantity guilliotine (total
from service) and set quantity before service (service In-
terval*)
5. operation Timer:
Actual ”on” time (Total from service)
and set time before service (service Interval*)
6. Print out:
Prints the screen of ”Timers/Counters.
7. Last service date:
Information of last service. reset
after service*
8. Prev:
closes this menu and open previous menu.
9. Home:
Press to return to ”Main”menu.
*service Interval should be adjusted to match about one
years production (one shift).
the parameters only accessible with a password and reser-
ved for service personell only.
Service Request” will
appear on the order menu
when counter or timer has
reached the set interval.
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 24
7.53 I/O Control Input - Output
This menus are for monitoring only and can be used for troubleshooting of PLC I/O signals.
0 = signal is off, 1= signal is on.
1.
Prev:
Return to previous menu.
2.
Home:
Return to "Main" menu.
.
1
2
1
2
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 25
7.54 TIMERS/ COUNTERS
This menu is for setting energy saving parameters and service intervals.
1.
Delay time cut:
Set the wanted idling time for the cut motor when cut sequence not is
running.
2.
Delay time conveyor:
Lengthen the conveyor feeding time.
Value "0" = start and stopp is the same as for the belt unit in cutting machine.
3.
Counter Blade:
Actual cut quantity on cutting blade (Total from service) and set
quantity before service (Service Interval*)
4.
Counter Knife:
Actual cut quantity guilliotine (Total from service) and set quantity
before service (Service Interval*)
5.
Operation Timer:
Actual "on" time (Total from service) and set time before
service (Service Interval*)
6.
Print Out:
Prints the screen of "Timers/Counters.
7.
Last service Date:
Information of last service. Reset after service*
8.
Prev:
Closes this menu and open previous menu.
9.
Home:
Press to return to "Main" menu.
*Service Interval should be adjusted to match about one years production (one shift).
The parameters are only accessible with a password and reserved for service
personell only.
9
1
2
3
4
5
6
8
7
"Service Request" will
appear on the Order menu
when counter or timer has
reached the set interval.
See 3,4,5 below.
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 25
7.54 TIMERS/ COUNTERS
This menu is for setting energy saving parameters and service intervals.
1.
Delay time cut:
Set the wanted idling time for the cut motor when cut sequence not is
running.
2.
Delay time conveyor:
Lengthen the conveyor feeding time.
Value "0" = start and stopp is the same as for the belt unit in cutting machine.
3.
Counter Blade:
Actual cut quantity on cutting blade (Total from service) and set
quantity before service (Service Interval*)
4.
Counter Knife:
Actual cut quantity guilliotine (Total from service) and set quantity
before service (Service Interval*)
5.
Operation Timer:
Actual "on" time (Total from service) and set time before
service (Service Interval*)
6.
Print Out:
Prints the screen of "Timers/Counters.
7.
Last service Date:
Information of last service. Reset after service*
8.
Prev:
Closes this menu and open previous menu.
9.
Home:
Press to return to "Main" menu.
*Service Interval should be adjusted to match about one years production (one shift).
The parameters are only accessible with a password and reserved for service
personell only.
9
1
2
3
4
5
6
8
7
"Service Request" will
appear on the Order menu
when counter or timer has
reached the set interval.
See 3,4,5 below.
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 24
7.53 I/O Control Input - Output
This menus are for monitoring only and can be used for troubleshooting of PLC I/O signals.
0 = signal is off, 1= signal is on.
1.
Prev:
Return to previous menu.
2.
Home:
Return to "Main" menu.
.
1
2
1
2
