background image

2

Thank you for purchasing your
Hydromatic

®

pump. To help

ensure years of trouble-free 
operation, please read the 
following manual carefully.

Before Operation: 

Reasonable care and safe methods
should be practiced. Check 
local codes and requirements
before installation.

Attention: 

This manual contains important
information for the safe use of
this product.  Read this manual
completely before using this
product and refer to it often for
continued safe product use.
DO NOT THROW AWAY OR
LOSE THIS MANUAL.  Keep it
in a safe place so that you may
refer to it often.

WARNING: Before handling
these pumps and controls,
always disconnect the power
first. Do not smoke or use 
sparkable electrical devices or
flames in a septic (gaseous) or
possible septic sump.

1. Most accidents can be avoided

by using COMMON SENSE.

2. Read the operation and

maintenance instructions
manual supplied with the
pump.

3. Do not wear loose clothing

that can become entangled 
in the impeller or other 
moving parts.

4. This pump is designed to

handle materials that could
cause illness or disease
through direct exposure.  Wear
adequate protective clothing
when working on the pump 
or piping.

Electrical:

5. To reduce the risk of 

electrical shock, pump must
be properly grounded in
accordance with the National
Electric Code and all 
applicable state and local
codes and ordinances.

6. To reduce risk of electrical

shock, disconnect the pump
from the power source before
handling or servicing.

7. Any wiring to be done on

pumps should be done by a
qualified electrician.

8. Never operate a pump with a

power cord that has frayed or
brittle insulation.

9. Never let cords or plugs lie in

water.

10. Never handle connected

power cords with wet hands.

Pumps:

11. Pump builds up heat and

pressure during operation;
allow time for pump to cool
before handling or servicing.

12. Only qualified personnel

should install, operate or
repair pump.

13. Keep clear of suction and

discharge openings.  DO NOT
insert fingers in pump with
power connected.

General
Information

Pump
Introduction

14. Do not pump hazardous

material not recommended for
pump Group 1, Div. 1, Class D
(flammable, caustic, etc.).

15. Make sure lifting handles are

securely fastened each time
before lifting.

16. Do not lift pump by the 

power cord.

17. Do not exceed manufacturer’s

recommendation for maximum
performance, as this could
cause the motor to overheat.

18. Secure the pump in its

operating position so it cannot
tip over, fall or slide.

19. Keep hands and feet away

from impeller when power 
is connected.

20. Submersible sump pumps

are not approved for use in
swimming pools, recreational
water installations, decorative 
fountains or any installation
where human contact with the
pumped fluid is common.

21. Do not operate pump without

safety devices in place.

22. For hazardous locations, use

pumps that are listed and
classified for such locations.

IMPORTANT: Hydromatic is not
responsible for losses, injury 
or death resulting from a 
failure to observe these safety
precautions, misuse or abuse 
of pumps or equipment.

Содержание SPX50

















Отзывы: