HydroHoist 18000 Long Скачать руководство пользователя страница 17

Страница: 17 / 51

Rev. 07142020

STEP 3: ATTACH TANK FRAME BRACKETS TO STRAP PLATES

Bolt

Support Channel

Bottom Gasket

Nylon Bushing (2)

Flathead Bolt

Attach Zip Ties

Part #

Parts Required (Per Tank)

LPL

1040

Channel Support

LPL

1027

Bottom Gasket

LPL

1025

Strap Plate

Part #

Hardware Required

LPL

1504

Bolt (3/8

16 x 3 x 6)

LPL

1006

Flat Head Bolt

(5”

SS)

LPL

1031

Nylon HH Tank Bushing

1926

Hex Nut (1/2

13 Brass)

1916

Lock Washer

Align the mounting holes for the Channel Support, Strap Plate, and Bottom Gasket.

Slide the U

Bolts through the bottom of the Channel Support.

Assembly Aid: Attach Zip Ties to the bases of the U

Bolts to keep them in place during installation. Zip Ties are

not provided in the kit.

Insert the

5”

Flat Head Bolt through the Channel Support and the Bottom Gasket.

IMPORTANT: Tighten the Nuts against the Nylon Bushing so the Bolts cannot rotate before assembling into the
tank. This will make it easier to assemble the Bottom Gasket in Step 4.

Use Kit Box: #HH

2650

Lock washer

Hex Nut

Lock washer

Hex Nut

Strap

Содержание 18000 Long




















































Результаты поиска

Содержание 18000 Long

Отзывы:

Похожие инструкции для 18000 Long

Бренды по названию

Популярные бренды

HydroHoist 18000 Long, Руководство по установке

Результаты поиска

Содержание 18000 Long

Отзывы:

Похожие инструкции для 18000 Long

Бренды по названию

Популярные бренды