background image

6

2.OO installation

2.O1 Site Survey & Installation Requirements

• 

Unit must not be installed near areas that suffer excess temperature changes, direct sunlight, frost or moisture 
of any kind.

• 

Area must be free of high levels of electrical noise.

• 

Ensure the unit can be mounted in an accessible position above the height of the required discharge location.

• 

Unit must be mounted on a suitable wall, that is flat and perpendicular to the floor.

• 

The unit location should be well lit for any maintenance and free of high levels of dust / air particulates.

• 

Scheduled maintenance should be carried out on the dispenser at least once per year.

2.O2 Wall Mount

1) Choose an installation location that is:

• 

Within 1.5m (4.5 ft.) of the product containers.

• 

At a reasonable height above the wash tank on the dish machine that allows for easy maintenance access.

• 

Away from any direct sources of steam, water spray, and high temperatures.

• 

Close enough to the dish machine electrical control panel to allow dispenser wiring without use of an external junction box 
(not provided) wherever possible.

2) Use the mounting bracket to mark the appropriate mounting location and as a hole template to mark the securing holes. 

3) Wall anchors are provided, please ensure they are appropriate to the wall/surface being mounted to.

4) Attach mounting bracket to mounting surface with hardware 

provided.

5) Hang unit on bracket.

WARNING! 

This product is intended to be installed by experienced installers, in accordance with all applicable 

electrical and plumbing codes.

Hang Unit on Bracket

60.5mm

(2.4 in)

Wide

Mounting Bracket

72mm

(2.8 in)

High

Back of Unit

Mounting Bracket

Содержание CP-5OO

















Отзывы: