HydraMaster The Master's Touch TMT 3000 Скачать руководство пользователя

Страница: 83 / 119

Systems Troubleshooting: 8-10

VaCUUM SySTeM

1.0 a weak vacuum at wand. The gauge reads normal.

1.1 Blockage in the hoses or

wand tube

Disconnect the hoses and check for an obstruction.

1.2 excessive length of

hose connected to the

truckmount

Do not attach excessive lengths of hose.

2.0 a weak vacuum

2.1 Air leak somewhere in the

vacuum system.

Check the vacuum relief valve for proper adjustment.

Carefully check all the vacuum hoses for a cut or

break.
Check the recovery tank lid gasket.
Make sure the recovery tank drain valve is fully

closed.

2.2 The vacuum blower is

turning too slowly.

Check the rpm of the engine. Adjust as necessary to

3,200 rpm under no vacuum load.

2.3 The vacuum gauge is

defective.

Test the gauge and replace if necessary.

3.0 The vacuum gauge reads too high with no hoses attached

3.1

The filter in recovery tank

is clogged.

Remove and clean or replace as necessary.

3.2 The hose from recovery

tank to the vacuum blower

is collapsed internally.

Inspect and replace as necessary.

4.0 excessive noise produced by the blower

4.1 The blower is low on oil.

Inspect the oil levels and replenish as necessary. Note:

Running the blower with low oil levels can cause severe

damage. If this situation occurs the blower should be

inspected by a qualified service technician.

4.2 The vacuum blower has

internal damage.

Refer to a qualified service technician.

Содержание The Master's Touch TMT 3000
























































































































Результаты поиска

Содержание The Master's Touch TMT 3000

Отзывы:

Похожие инструкции для The Master's Touch TMT 3000

Бренды по названию

Популярные бренды

HydraMaster The Master's Touch TMT 3000, Руководство пользователя

Результаты поиска

Содержание The Master's Touch TMT 3000

Отзывы:

Похожие инструкции для The Master's Touch TMT 3000

Бренды по названию

Популярные бренды