HydraMaster The Master's Touch TMT 3000 Скачать руководство пользователя

Страница: 12 / 119

General Information: 1-6

Warnings and Cautions specific to the TMT 3000 include the following:

During the operation of the truckmount many components are in motion. Never

touch any part of the truckmount that is in motion. Serious injury may result.

During the operation of the truckmount many surfaces will become extremely hot.

Never touch hot surfaces. Serious injury may result.

The operation of this truckmount can produce noise levels exceeding 85 decibels

to a distance of 10 ft (3.05 m). The Occupational Safety and Health Administration

(OSHA) recommends the use of hearing protective equipment if a person is

exposed to an average of 85 decibels over an 8-hour period. Check with local

and state agencies concerning hearing conservation rules.

During the operation of the truckmount carbon monoxide and other toxic fumes

are produced. Position the vehicle so that any fumes produced will be directed

away from inhabited areas and any points of building entry (doors, windows, air

conditioning units, fans, etc.). Do not occupy the vehicle while the truckmount is

in operation. Serious injury may result.

During the operation of the truckmount, chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm are produced by the

engine exhaust.

Never operate the truckmount with a portable gas container inside the vehicle.

Doing so will increase the risk of fire and explosion. Serious injury or death may

result. See page 1-10 of this Owner’s Manual for more information.

Transporting a vented fuel container that presently contains, or has ever contained

in the past, a flammable liquid is strictly forbidden by HydraMaster and by federal

and state regulations. Doing so will increase the risk of fire and explosion. Serious

injury or death may result.

Содержание The Master's Touch TMT 3000
























































































































Результаты поиска

Содержание The Master's Touch TMT 3000

Отзывы:

Похожие инструкции для The Master's Touch TMT 3000

Бренды по названию

Популярные бренды

HydraMaster The Master's Touch TMT 3000, Руководство пользователя

Результаты поиска

Содержание The Master's Touch TMT 3000

Отзывы:

Похожие инструкции для The Master's Touch TMT 3000

Бренды по названию

Популярные бренды