HydraMaster CDS 4.8 Скачать руководство пользователя

Страница: 10 / 141

HydraMaster Corporation

Page 1-4

Clutch Drive System

ACID RINSE AGENTS

: The increased demand for clear water rinsing results in the

need for special care when using these acid based chemicals in your equipment. The

negative side of these products is the corrosive effects the acid can have on metals,

including swivels, pumps, heat exchangers, etc.

HydraMasters

ClearWater Rinse

has been formulated to protect vital components.

HydraMaster will not warranty parts that have been damaged from using unprotected

acid products that have obviously caused failures.

HARD WATER PROTECTION

: Failure to take appropriate measures to prevent scale

build up can result in

system failure

and

loss of warranty

on affected parts. Test the

water in your immediate and surrounding areas with hard water test strips. Assume

all water obtained from wells is hard. If you are operating in a AHard Water Area@

(3.5 grains or more per gallon), use a water softening system.

FREEZE PROTECTION

: There is often little warning before a cold spell. Therefore,

not protecting this equipment from freezing will result in costly down-time. Placing

an electric heater in the truck or parking the truck indoors will help to insure against

freezing, but should not be the primary method of freeze protection.

HOT SURFACES

: During the operation of this equipment, many surfaces on the

machine will become very hot. When near the van for any reason care must be taken

not to touch any hot surface, such as heater, engine, exhaust, etc.

♦

CAUTION

♦

CAUTION

♦

CAUTION

♦

WARNING

♦

5/5/99

Содержание CDS 4.8














































































































































Результаты поиска

Содержание CDS 4.8

Отзывы:

Похожие инструкции для CDS 4.8

Бренды по названию

Популярные бренды

HydraMaster CDS 4.8, Руководство пользователя

Результаты поиска

Содержание CDS 4.8

Отзывы:

Похожие инструкции для CDS 4.8

Бренды по названию

Популярные бренды