HydraMaster CDS 4.8 Скачать руководство пользователя

Страница: 120 / 141

Clutch Drive System

Page 10-13

HydraMaster Corporation

CDS 4.8

5/5/99

No.

Problem/

Possible Cause

Solution

8.0 The pump clutch will not work.

8.1 The

pump clutch switch

in the mix

Replace the switch.

tank has failed.

8.2 The

lower float switch

in the mix

When the float is down, the circuit is

tank is defective.

open. When the float is up, the

circuit is closed. Replace the switch

if necessary.

In areas with high iron content in the

water, magnetic debris may accumu

late on the switch. Try wiping away

this debris to return function to the

switch.

8.3 There is no

power

getting to the

Locate any burnt, broken, or cut wire

clutch.

and repair as necessary. Also check

for and repair any loose connection.

8.4 There is a bad

ground

Check the blower frame ground

connection. Repair as necessary.

8.5 The

clutch

has failed.

Replace the clutch.

Содержание CDS 4.8














































































































































Результаты поиска

Содержание CDS 4.8

Отзывы:

Похожие инструкции для CDS 4.8

Бренды по названию

Популярные бренды

HydraMaster CDS 4.8, Руководство пользователя

Результаты поиска

Содержание CDS 4.8

Отзывы:

Похожие инструкции для CDS 4.8

Бренды по названию

Популярные бренды