background image

Damocles2

Damocles2

Damocles2

50

51

Digital Inputs (DI)

Parameters for DI (Dry Contact Inputs). Damocles inputs feature pulse counters; this can be 
used for example to read energy consumption meters with a pulse output (S0). Counters are in-
cremented whenever the input is closed. The pulse must be longer than 20 ms to be registered.

Counters are 32 bit (maximum value 4 294 967 295). Values are retained in memory even when 
the power is off. They can be reset (for the entire device) at the General Setup tab.

•  

Name

 – Name of the input, up to 12 chars (e.g. “left door”, “smoke room 1”).

•  

ID

 – Unique ID of the input variable within the device 

[1 – 32]

.

•  

Current Value

 – Current state of the input (“

O (Off)

”/“

1 (On)

“).

•  

Alarm State

 – Alarm state definition for each input.

  •  

Active if On

 – Alarm is active whenever the input is in 1 (On).

  •  

Active if Off

 – Alarm is active whenever the input is in 0 (Off).

  •  

Disabled

 – Input has no alarm state defined.

•  

Delay [s]

 – Delays the sending of information about alarm beginning and alarm end.

•  

Out of Safe Range

 – Response to the Alarm state activation/deactivation for dry contact inputs.

•  

SNMP Trap

 – Enables sending a SNMP trap upon alarm activation/deactivation.

•  

E-mail

 – Enables sending an e-mail upon alarm activation/deactivation.

•  

SMS

 – Enables sending a SMS upon alarm activation/deactivation.

Note:

 

SMS (text messages) are sent through a GSM modem connected directly to the Damocles2 unit via 

the RS-232 interface (see the list of Damocles2 models), or via a remote HWg-SMS-GW3. 

The Alarm state for each DI is only active when assigned to an action (sending an e-mail, SMS 
or SNMP Trap). Nothing checked = no active alarm for the DI input (yellow status in the table at 
the home page). It is recommended to activate SNMP Trap to notify alarms.

Alarm status notification based on a Delay value:  

• 

Blue: 

Delay = 0

•  

Yellow:

 Delay is set

Web interface

Web interface

Alarm state

Alarm 

STA

RT

 notification

Alarm 

END

 notification

Alarm 

STA

RT

 notification

Alarm 

STA

RT

 notification

Alarm 

END

 notification

Alarm 

END

 notification

Time

Delay [s]

Содержание Damocles2 1208




































Отзывы: