15
2.3 Installation of machine
2.3.1 Put the anchor bolts on the machine base when installing the machine, then
put the machine on the groundwork, put the sizing block underlay the machine.
2.3.2 Clean the antirust oil on the base, column, arm, spindle and other surface.
2.3.3 Adjust the level initially: adjust the sequence of the sizing block according
to 1,2,3,4 in groundwork picture 2.1.
2.3.4 Remove the locking screw (1) according to picture 2.3, joint the clamp oil
pipe.
2.3.5 Remove the locking plate according to picture 2.4.
2.3.6 Electric installation:
2.3.6.1 Lifting motor installation (see picture 2.5)
Fixing the motor in correct way and fix the bolt. Open up the junction box,
connect the leads according to the numbers, then cover it and screw down.
2.3.6.2 Connect the leads of main power.
2.3.7 Check the correctness of power supply phase sequence (picture 3.1)
：
push
the button 1-18, check whether the headstock is loose (or push button 1-19, check
the headstock and see whether it is clamped); push elevating button 1-3 on the
arm
，
move the arm up by 10mm
，
check whether it is lifting or not (or push the
down button 1-2
，
check whether it is lowering).
2.3.8 Push the falling button 1-2(picture 3.1)
，
make the arm come down 10mm
，
clean the antirust oil on the top of column, move the arm up 10mm again, clean
the antirust at the bottom of the column, repeat the work until the oil is rubbed up.
Push the button to loosen the headstock, turn the moving handwheel 1-10, move
the headstock to the left side, clean the antirust oil on the guideway, then reset and
clamp the headstock.
2.3.9 Trickle the lubricating oil on the surface of the column, then move the arm
50mm down, clean and lubricate the bare section again, move the arm 100mm up,
clean and lubricate the bare section adequately, so you can lift and lower the arm
in a large extend.
Attention: Do not scratch the surface of the column, oiling them according to the
lubricating list in picture 2.6 and check the lubricating situation, and immit the
Содержание CRDM 3050 x 16/1
