background image

IMPACT Rear Roll-in

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483  U.S.A.

P/N 0435045A

6-1

REPLACING FAN MOTORS AND BLADES

See cross section for location of evaporator and
return air fans. Should it ever be necessary to
service or replace the fan motors or blades be
certain that the fan blades are re-installed 
correctly. 

For access to evaporator fans:

1. Turn off power.

2. Remove upper shelving.

3.

Disconnect fan from wiring harness.

4. Remove fan mounting panel from coil 

module. 

5. Remove wire fan guard.

6. Remove fan blade.

7. Remove screws holding bottom of motor to

fan basket.

8. Replace fan motor and blade.

9. Re-install fan mounting panel in coil module.

10. Reconnect fan to wiring harness.

11. Turn on power. Verify that motor is working

and blade is turning in the correct direction.

12. Ensure the fan plenum is located properly

and that there are no air leaks which would
adversely affect case performance.

13. Bring case to operating temperature before

restocking.

For access to return air fans:

1. Turn off power.

2. Remove dairy carts, or bottom shelving.

3. Remove return air grille.

SERVICE

Always disconnect the electrical power at
the main disconnect when servicing or
replacing any electrical component. This
includes, but is not limited to, such items
as fans, heaters, thermostats and lights.

WARNING

!

Fan Plenum 

in Front 

Package

(Lifts Out)

Fan Blade 

Case 

Interior

Wiring 

Harness

Electrical

Connection 

Box

Содержание IMPACT D5RRI



























Отзывы: