Husqvarna 325HDA Скачать руководство пользователя страница 35

Страница: 35 / 40

503 98 96-01

Turn the upper connecting rod with
the pin from the gear towards you.

Fit the washer.

Fit the lower eccentric cam.

The lower eccentric cam is displaced
a 1/2 turn in relation to the upper
eccentric cam.

Fit the left-hand threaded nut. Tight-
ening torque 30 Nm.

Fit the clutch drum’s gear, clutch
drum, washer and screw. Secure the
screw using weak thread lock fluid.
Tightening torque 12 Nm.

Thread the axle in the gear.

Fit the upper eccentric cam.

Fit the upper connecting rod.

Assembling the gearbox

325HS75, 325HS99:

Lubricate the components with
grease 503 98 96-01 when
assembling.

Fit the gear assembly.

Fit the cutting equipment.

Fit the support plate.

Guide in the connecting rod’s pin in
the blade and fit the cutting
equipment’s screws.

Tighten the lock nuts. Counter hold
the screws inside the gearbox.
Check that the cutting equipment’s
washer moves. If the washer does not
move loosen the hexagonal screw
max. a 1/4 turn.

Turn the lower connecting rod so that
the pin fits in the cutting unit.

Fit the lower connecting rod.

Fit the felt seal.

Fit the flat washer on the gear
assembly’s axle.

Fit the thrust washer on the gear
assembly’s axle.

Fit the guide plate.

Fill the angle gear with 1 1/2 tubes of
grease 503 98 96-01.

Check that the cover’s O-ring seal is
in the right position and fit the cover.

Secure the O-ring seal with grease.
Hold the cover with your thumb.
Tighten the screws on the cover
crosswise.

Cutting equipment

NOTE!

The connecting rod has a needle
bearing on the big end, exercise
great care so that it does not fall
apart. The needles (53) are loose in
the holder.

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 325HDA









































Результаты поиска

Содержание 325HDA

Отзывы:

Похожие инструкции для 325HDA

Бренды по названию

Популярные бренды

Husqvarna 325HDA, Руководство по ремонту

Результаты поиска

Содержание 325HDA

Отзывы:

Похожие инструкции для 325HDA

Бренды по названию

Популярные бренды