Huskie Tools HH100, Руководство по обслуживанию

Страница: 26 / 64

26
5. SPECIFICATIONS
Table 10. Specifications by Model
ITEM UNIT HH100 HH150-2 HH300-2 HH500-2 HH750-2 HH1000-2
Impact
Energy Class ft-lbs.
kg-m 100
14
200
28
350
49
575
81
825
116 1200
168
Adjustable
Blows Per
Minute
bpm 700-1300 520-1170 590-1200 510-1,180 600-1080 500-860
Required Oil
Flow gpm
l/min 4-7
20-45
5-12
20-45
8-16
30-60
9-18
35-70
13-24
50-90 16-35
60-130
Operating
Pressure psi
bar
1,000-
2,275
69-160
1,014-
1,867
70-129
1,294-
1,867
89-129
1,441-
1,867
99-129
1,441-
2,161
99-149
1,720-2,587
119-178
Nitrogen Gas
Pressure psi
bar 140-160
10-11
190-210
13-14
190-210
13-14
160-185
11-13
190-210
13-14
190-210
13-14
Total Weight
with Tool lbs.
kg 165
154 340
154 520
236 550
250 800
363 1,100
500
Total Length
inch
mm 35
889
50
1,270
52
1,321
54
1,372
64
1,626
73
1,854
Tool Diameter
inch
mm 1.6
40
2.0
50
2.4
60
2.6
65
3.0
75
3.5
90
Applicable
Carrier
Tons .75-2.25 1.25 – 3.25 2.25 - 6 2.75 - 7 3.35 – 8 3.5 - 12
Remarks:
•
The hammer is to be used within the specified oil pressure, oil flow and gas pressure parameters.
•
The carrier hydraulic system relief pressure is to be set at 600 to 800 psi above the hammer
“Operating Pressure” measured at the hose end of the carrier (pressure hose) when disconnected
from the hammer.
•
The nitrogen charge in a hammer is directly related to the operating pressure of the circuit
powering it. An increase of 10% in gas charge will cause a 10% rise in hammer operating
pressure. This is prevalent in hammers if gas pressure has been set or checked on a cool morning
(60
0
F) and then run in increasingly higher ambient temperatures up to and over 100
0
F. This
increase in ambient temperature can cause the carrier operating pressure to rise past its relief
setting, stalling the hammer.
Table 11. Recommended Gas Pressure Based Upon Ambient Temperature
*
*
Gas pressure should be set bearing in mind the possible high ambient temperature
potential for that day’s work. While unlikely, a setting that will run well on a hot day
may run erratically until the hammer warms up thoroughly . Please contact IPC
Industries, Inc. if you have any questions.
Hammer Model Standard Pressure 80
0
F 90
0
F 100
0
F 110
0
F 120
0
F
HH100 140 – 160 psi 160 psi 150 psi 140 psi 130 psi 120 psi
HH150-2 190 – 210 psi 210 psi 200 psi 190 psi 180 psi 170 psi
HH300-2 190 – 210 psi 210 psi 200 psi 190 psi 180 psi 170 psi
HH500-2 160 – 185 psi 185 psi 175 psi 160 psi 150 psi 140 psi
HH750-2 190 – 210 psi 210 psi 200 psi 190 psi 180 psi 170 psi
HH1000-2 190 – 210 psi 210 psi 200 psi 190 psi 180 psi 170 psi