HURST ML-630-SI Скачать руководство пользователя страница 30

Страница: 30 / 48

11.3.1 Replacing and cleaning the air fi lter

Procedure:

If present, remove the rear side panel of the hydraulic power unit, in that the

xing clip and

the side panel are removed.
1. Unscrew both bolts from the air

lter cover and remove the cover.

2. Remove the foam air

lter insert from the cover.

3. Take the paper air

lter insert from the air

lter housing.

4. Check both air

lter inserts and replace if damaged. The paper air

lter insert must always

be replaced at planned intervals.

5. Clean the air

lter inserts if reusing them.

Paper air fi lter insert

: Tap out the paper air

lter insert a few times on a hard surface to

remove dirt or blow compressed air [not more than 207 kPa (2.1 kg/cm )] from the air

lter

housing side through the

lter insert. Never attempt to brush out dirt because it would be

pressed in by the bristles. Replace the paper air

lter insert if it is exceedingly dirty.

Foam air fi lter insert:

Clean in warm soapy water, rinse and allow to dry thoroughly.

Or clean in non-

ammable solvent and let dry. Do not introduce any oil to the foam air

lter insert.

6. Wipe away dirt from the inside of the air

lter housing with a damp cloth. Ensure that dirt

does not penetrate the air duct leading to the carburettor.

7. Then re-

t the

lter.

NOTE:

Keeping the air

lter in good condition is extremely important. Penetrating

dirt leads to damage and wear in the engine in case of incorrect installation,
incorrect damage or unsuitable

lter inserts.

Always keep the air

lter insert clean.

Air

lter cover

Bolts

Foam air

lter insert:

Paper air

lter insert:

Air

lter housing

Содержание ML-630-SI

















































Результаты поиска

Содержание ML-630-SI

Отзывы:

Бренды по названию

Популярные бренды

HURST ML-630-SI, Инструкция по эксплуатации

Результаты поиска

Содержание ML-630-SI

Отзывы:

Бренды по названию

Популярные бренды