Hurricane 11042, Оригинальная инструкция по эксплуатации

Страница: 21 / 216

4. Technical data
Engine displacement 49.3 cm 3
Maximum engine capacity 2.2 kW
Bar length 44 cm
Cutter rail length 18” (45 cm)
Chain pitch (0.325”), 8.255 mm
Chain thickness (0.058”), 1.47 mm
Idling speed 3000 ± 300 rpm
Maximum speed with cutting equipment 11000 rpm
Chain speed max. 21.2 m/s
Tank capacity 550 cm 3
Oil tank capacity 260 cm 3
Anti-vibration function Yes
Chain wheel teeth 7 x 8.255 mm
Chain brake Yes
Clutch Yes
Automatic chain lubrication Yes
Low-kickback chain Yes
Net weight without chain and chain bar 5.4 kg
Net weight (dry) 6.7 kg
Fuel consumption (specific) 560 g / kWh
LPA sound pressure level (ISO 22868) 100.6 dB(A)
KPA uncertainty 2.5 dB(A)
LWA sound power level measured
(ISO 22868) 111.9 dB(A)
KWA uncertainty 2.5 dB(A)
LWA sound power level guaranteed
(ISO 2000/14/EC) 114 dB(A)
Ahv vibration (front handle)
(ISO 22867) max. 6.6 m/s 2
Khv uncertainty 1.5 m/s 2
Ahv vibration (rear handle)
(ISO 22867) max. 6.91 m/s 2
K
hv
uncertainty 1.5 m/s 2
Chain type Oregon 21BPX072X
Bar type Oregon 188PXBK095
Spark plug L8RTF
Keep the noise emissions and vibrations to a
minimum.
n
Only use appliances which are in perfect working
order.
n
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
necessary.
n
Switch the appliance off when it is not in use.
n
Wear protective gloves.
5. Before starting the equipment
Important: Do not start the engine until the saw
is fully assembled.
Important: Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
3. Using a screwdriver, run the adjustment screw (D)
COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3B/3C).
4.
Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3C/3D).
5.2 To install saw chain
1. Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
2. Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
3. Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
Note: The saw chain may droop slightly on the lower
part of bar. This is normal.
4. Pull the chain bar forward until the chain is closely
seated. Make sure that all the drive links are in the
groove of the bar.
5. Fit the coupling cover and fasten it with 2 screws.
The chain must not slip off the bar when you do
this. Make sure that the pin (Fig. 3C/Item E) fits
21
GB
Anleitung_MS_2245_SPK7__ 20.08.12 09:00 Seite 21