HURNER WeldControl 2.0 630, Руководство пользователя

Страница: 35 / 79

CODE : 415311
Version January 2019
EN
11 HÜRNER WeldControl 2.0 630 User’s Manual
H Ü R N E R S c h w e i s s t e c h n i k G m b H
Nieder-Ohmener Str. 26
35325 Mücke, Germany
********************
* HUERNER *
* WeldControl 2.0 *
********************
Display 1
4 Operation
Important
Important
ÐBCLOBÐQEBÐ@LKQOLIÐRKFQÐFPÐQROKBAÐLK Ð@EB@HÐQEBÐLFIÐIBSBIÐLCÐQEBÐ
hydraulic and control unit and top up with HF-E 15 hydraulic
oil as needed.
Important
The surfaces of the heating element have to be free of grease
>KAÐ@IB>K ÐLOÐQEBVÐE>SBÐQLÐ?BÐ@IB>KBA
Important
Make sure all connectors are tight in their sockets and note
that operation on a worksite is only acceptable if the power
supply has earth-leakage circuit breakers.
After connecting the power supply cord to the mains power supply or
>ÐDBKBO>QLO ÐQROKÐQEBÐJ>@EFKBÐLKÐ>QÐQEBÐ,K,CCÐPTFQ@E
Caution
It has to be ensured that the voltage of the power source the
machine is connected to corresponds to the rated voltage of
the machine. Also the following has to be respected when
using extension cables:
Ð "NMÆFTQHMFÐSGDÐ,@BGHMDÐ$MSDQHMFÐ6DKCHMFÐ/@Q@LDSDQR
CQBOÐQEBÐJ>@EFKBÐT>PÐPTFQ@EBAÐLK Ð!FPMI>VÐÐPELTPÐLKÐQEBÐP@OBBK
The machine will then automatically start the auto-test process to
check the sensors and the system clock and to determine the number
of free welding reports. This test can be bypassed by holding down
the STOP/RESET key when Display 1 is showing.
Caution
Ð&CÐAROFKDÐQEBÐ>RQLQBPQÐ>KÐBOOLOÐFPÐABQB@QBA Ð>Ðe0VPQBJÐ"OOLOsÐ
JBPP>DBÐPELTPÐLKÐQEBÐAFPMI>VÐ4EBKÐQEFPÐE>MMBKP ÐQEBÐTBIA
-
ing unit has to be disconnected immediately from the power
PRMMVÐ>KAÐEB>QFKDÐBIBJBKQC>@FKDÐQLLI Ð>KAÐFQÐE>PÐQLÐ?BÐOB
-
turned to the manufacturer for repair.
0R?PBNRBKQÐQLÐ>ÐPR@@BPPCRIÐ>RQLQBPQÐLOÐ>CQBOÐQEBÐQBPQÐT>PÐ?VM>PPBA ÐQEBÐ
machine first shows overview screens on the selected kind of machine
>KAÐTBIAFKDÐPQ>KA>OA ÐQEBKÐ!FPMI>VÐ
!FPMI>VÐÐPELTPÐQEBÐQEBÐA>Q>ÐLCÐQEBÐKBUQÐTBIAFKD ÐFK@IRAFKDÐQFJBÐLCÐ
A>V ÐA>QB ÐOBMLOQÐKRJ?BO Ð>KAÐGLFKQÐKRJ?BO Ð>ILKDÐTFQE ÐFKÐQEBÐPB@LKA
QLI>PQÐIFKB ÐQEBÐ>@QR>IÐFKMRQÐSLIQ>DBÐ>KAÐ ÐFCÐQEBÐ@>?IBÐLCÐQEBÐEB>QFKDÐ
BIBJBKQÐCLOÐ?RQQÐTBIAFKDÐFPÐ@LKKB@QBAÐ ÐQEBÐ>@QR>IÐ>KAÐKLJFK>IÐEB>Q
-
ing element temperature before and after the slash.
#OLJÐ!FPMI>VÐ ÐFQÐFPÐMLPPF?IBÐQLÐ>@@BPPÐQEBÐ LKCFDRO>QFLKÐ*BKRÐFKÐTEF@EÐ
the default behavior of the welding machine can be configured. To
>@@BPPÐFQ ÐMOBPPÐQEBÐ*"+2ÐHBVÐ>KAÐQEBK ÐLKÐQEBÐCLIILTFKDÐBKQBOÐ@LABÐ
P@OBBK ÐQVMBÐQEBÐ>@@BPPÐ@LABÐRPFKDÐQEBÐ@ROPLOÐHBVPÐLOÐELIAÐQEBÐQO>K
-
sponder card in front of the RFID reader.
Pressing the
×
and
Ø
Ð@ROPLOÐHBVPÐFKÐQEBÐJBKRÐQE>QÐ>MMB>OPÐ!FPMI>VÐ Ð
Welding Standard
DVS
Display 2
Next welding
15:44:52 29.05.12
112V 135C/220C
Rep. No. 00072/00002
Display 3
For 400 V power: wire section 2.5 mm² = max. 20 m long
wire section 4.0 mm² = max. 75 m long
wire section 10.0 mm² = max. 100 m long
402V
Ð 1LÐ LMBO>QBÐ QEBÐ TBIAFKDÐ PVPQBJ Ð ?BÐ PROBÐ QE>QÐ FQÐ FPÐ PBQÐ LKÐ >Ð
MOLMBO ÐIBSBIÐPROC>@BÐ>KAÐQE>QÐMLTBOÐPRMMIVÐMOLQB@QFLKÐFPÐÐÐ
PILTÐ?ILT