HunterDouglas Palm Beach Polysatin Скачать руководство пользователя страница 13

Страница: 13 / 60

INSTALLATION

Hang Strip

Bent Leaf Hinge

" Holes for

Installation Screws

Hang Strip Behind Panels

Hang Strip

Standard Hinge

" Holes for

Installation Screws

Hang Strip to Side of Panels

Standard Panel Systems with Hang Strip

NOTE:

If a Decorative Sill Cover was ordered, refer to page 39.

Step A. Install the Hang Strips

Attach the side hang strips inside or outside the opening.

➤

With outside mounts, be sure the hang strips are positioned the correct width apart and
at the correct height.

➤

Insert an installation screw into the top and bottom holes only, then set the screws into
the mounting surface.

➤

Tighten the screws snugly, but do not overtighten.

Step B. Mount the Panels

Hang the panels by fitting the pin end of the hinges into the hinge barrels.

Square and align the panels to the opening.

➤

Hang Strip Behind Panels.

necessary, adjust the bent-leaf hinges
by loosening the hinge screws and
moving the hinge left or right.

➤

Hang Strip to Side of Panels.

necessary, place hinge shims between
the hinge and hang strip.

➤

Re-tighten the hinge screws once the
panels are square and aligned.

Standard Panel Systems with Hang Strip

Incorrect

Correct

Содержание Palm Beach Polysatin





























































Результаты поиска

Содержание Palm Beach Polysatin

Отзывы:

Похожие инструкции для Palm Beach Polysatin

Бренды по названию

Популярные бренды

HunterDouglas Palm Beach Polysatin, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание Palm Beach Polysatin

Отзывы:

Похожие инструкции для Palm Beach Polysatin

Бренды по названию

Популярные бренды