Hunter GSP9700 Series Скачать руководство пользователя страница 62

Страница: 62 / 157

The BDC laser locator automatically displays a vivid line at bottom dead center after
a wheel has been spun. The laser turns off when the wheel is spun again.

CAUTION:

Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.

With the servo enabled, attach the adhesive weight using the weight amount shown
for the right weight plane on the LCD.

Refer to “Servo-Aided Adhesive Weight

Placement,” page 61.

If servo is not enabled, BDC placement should be used.

Refer

to “Manual Weight Position Measurement,” page 59.

If necessary, use the right “

” to split the weight.

Refer to “Split Weight®

Feature,” page 82.

Left and right weight plane displays should show “OK” after check spin.

MIXED WEIGHTS balancing procedure is complete.

Balancing Procedures

GSP9720JLR Wheel Balancer Operation Instructions

Содержание GSP9700 Series






























































































































































Результаты поиска

Содержание GSP9700 Series

Отзывы:

Hunter GSP9700 Series, Руководство по эксплуатации, Страница: 62 / 157

Результаты поиска

Содержание GSP9700 Series

Отзывы: