Hunter GSP9700 Series страница 89 Скачать руководство пользователя | Manualshive

Страница: 89 / 157

background image

4. ROAD FORCE

®

MEASUREMENT

PROCEDURES

4.1 Load Roller Operation

The load roller runs parallel to the tire and applies a perpendicular load on the
assembly to take Road Force® Measurements. It is capable of applying up to 1400
pounds of force. The amount of force placed on the tire is dependent upon the tire’s
diameter and stiffness. The load roller will not overload the tire.

NOTE:

It is important that the air pressure of the tire is set to
specifications prior to the Road Force® Measurement.
Incorrect tire pressure will affect the results. If the

GSP9720JLR

is equipped with the Inflation Station feature,

the tire can be easily set to the specified air pressure.

Refer

to “Inflation Station,” page 106.

The load roller can be enabled and disabled by turning the control knob. When the
load roller is enabled, the LCD will display the load roller on the screen as shown
below.

Road Force with Limits Enabled: when the load roller selection is made, “LT Tires,”
“P-SUV Tires,” or “P Tires” road force specifications can be highlighted by slowly
turning the knob to the appropriate selection. Changing the “LT Tires,” “P-SUV Tires,”
or “P Tires” selection will change the limit specifications for road force and rim runout.

Refer to “Setting Up the Runout & Road Force Units,” page 114.

NOTE:

The load roller cannot be enabled in “Bare Rim Spin” mode.

When the load roller is disabled, only a balance spin will be performed. This can be
useful for a balance check spin after weights have been applied.

GSP9720JLR Wheel Balancer Operation Instructions

Road Force® Measurement Procedures

x

81

«
...
87
88
89
90
91
...
»

Содержание GSP9700 Series






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для GSP9700 Series

Бренд: Ranger Страницы: 60

Бренд: WilTec Страницы: 5

Бренд: WilTec Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды