manualshive.com logo in svg

Hunter GSP9700 Series, Руководство по эксплуатации, Страница: 130 / 157

Поделиться
Скачать
Hunter GSP9700 Series Скачать руководство пользователя страница 130

Place the calibration tool on the shaft using the middle spindle shaft slot. Align the 
center hole of the calibration tool with a calibration weight thread hole, and tighten 
the calibration weight securing the calibration tool to the hub face as shown below. 

 CAUTION: 

Do NOT operate balancer with calibration tool attached. 
Remove calibration tool immediately after performing this 
procedure.

Press “OK” when calibration tool is installed. 

Rotate the calibration tool slowly by hand, clockwise until the 

GSP9720JLR

 beeps.  

NOTE: 

You may have to rotate the tool up to 1 1/2 turns. 

Position the calibration tool parallel to the floor. Tap the foot pedal once or press “OK.” 

NOTE: 

To verify that the tool is parallel to the floor, measure from 
both ends of the calibration tool to the floor. The 
measurement will be the same at both ends when the tool is 
parallel to the floor.  

122

x

 Calibration and Maintenance 

GSP9720JLR Wheel Balancer Operation Instructions 

Содержание GSP9700 Series






























































































































































Отзывы:

Нет отзывов