Hunter GSP9700 Series страница 66 Скачать руководство пользователя | Manualshive

Страница: 66 / 157

background image

Set two of the widest weighted balance patches available side-by-side on
the tread directly above where the left and right weighted patches will be
installed inside of the tire. The patches should be positioned as far apart
from each other as possible, but should not be placed in the sidewall or
shoulder area of the tire.

Mark the tire tread at the center of the patches for future placement
reference and remove the patches from the wheel.

Place outer Dataset® arm roller directly over the left mark and enter data
by depressing the foot pedal.

Place outer Dataset® arm roller directly over the right mark and enter
data by depressing the foot pedal.

Close safety hood.

Press the green “START” button if “Hood Autostart” is disabled.

After wheel stops spinning, raise the safety hood.

Press the green “START” button with the safety hood in the RAISED position and the

GSP9720JLR

will find TDC for the left weight plane. Mark the tire’s inner sidewall for

patch placement.

Press the green “START” button with the safety hood in the RAISED position and the

GSP9720JLR

will find TDC for the right weight plane. Mark the tire’s outer sidewall

for patch placement.

Place an aligning mark on the tire and rim to align them back together after applying
the patch weights.

Remove wheel from balancer and dismount tire from rim.

Install left weight plane weighted balance patch(s) at mark(s) as instructed by
manufacturer's instructions.

Install right weight plane weighted balance patch(s) at mark(s) as instructed by
manufacturer's instructions.

Mount tire onto rim, aligning rim and tire marks.

Finish the patch balancing procedure by returning to the appropriate balance
procedure for the type of wheel being balanced. Verify balance condition by spinning
again, and attach weights as necessary to correct for residual imbalance.

PATCH balancing procedure is complete.

58

x

Balancing Procedures

GSP9720JLR Wheel Balancer Operation Instructions

«
...
64
65
66
67
68
...
»

Содержание GSP9700 Series






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для GSP9700 Series

Бренд: Atlas Страницы: 17

Бренд: Atlas Страницы: 23

Бренд: Fasep Страницы: 22

Бренд: Cormach Страницы: 19

Бренд: Cormach Страницы: 44

TOUCH MEC 1000 SONAR

Бренд: Cormach Страницы: 54

Бренд: Cormach Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды