Hunter GSP9700 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 157

Hunter GSP9700 Series Скачать руководство пользователя страница 35

CAUTION

:

Quick-Thread does not tighten the wing nut! In Quick-Thread
rotation, torque allowed is minimal. Therefore, the wing nut
must still be hand-tightened before balancing.

NOTE:

Also because of the software limited torque control, you
must

loosen

the wing nut before Quick-Thread will remove

it.

Quick-Thread will not operate under the following conditions:

If the balancer is in “Diagnostics,” “Setup,” or “Calibration.”

If either Dataset® arm is out of its “home position” while in the “Balance,”
“Current Runout & Loaded runout” or “Measure Rim Runout” screens.

3.4 CenteringCheck® Wheel Centering Feature

The CenteringCheck® wheel centering feature using Imbalance Forces or Location
can be used to inspect each mounting to identify possible centering errors, thus
preventing improper measurements from occurring.

CenteringCheck® may be used with either a “bare rim” or a “rim with tire assembly.”
On-screen prompts lead you through the procedure as follows:

Select “Perform CenteringCheck” from the menu.

GSP9720JLR Wheel Balancer Operation Instructions

Balancing Procedures

x

27

«
...
33
34
35
36
37
...
»

Содержание GSP9700 Series






























































































































































Отзывы:

Нет отзывов