Humminbird CHIRP страница 32 Скачать руководство пользователя

Страница: 32 / 40

Ret

Befo
Repa

Plea
the
Req
Auth

For

Humminbird Service Policy

Even though you’ll probably never need to take advantage of our incredible service policy, it’s good to know

that we back our products this confidently. We do it because you deserve the best. We will make every

effort to repair your unit within three business days from the receipt of your unit at our factory. This does

not include shipping time to and from our factory. Units received on Friday are typically shipped by the

following Wednesday, units received Monday are typically shipped by Thursday, etc.

All repair work is performed by factory-trained technicians to meet exacting factory specifications. Factory-
serviced units go through the same rigorous testing and quality control inspections as new production
units.

Warranty & Service Policy

CHIRP_Radar_Install_Manual_532523-1EN_A.qxp_Layout 1 8/11/16 10:48 AM Page 24

Содержание CHIRP









































Результаты поиска

Содержание CHIRP

Отзывы:

Похожие инструкции для CHIRP

Бренды по названию

Популярные бренды

Humminbird CHIRP, Руководство по установке

Результаты поиска

Содержание CHIRP

Отзывы:

Похожие инструкции для CHIRP

Бренды по названию

Популярные бренды