Humminbird CHIRP Скачать руководство пользователя

Страница: 30 / 40

Reg

As y

keep

•

Hum

from

reta

or r

Hum

has

the

This

•

Plea

serv

THIS

ON T

ANY

DUR

HUM

ANY

Som

dam

state

7. Test the Installation

Perform the following tasks before using the product on the water:

• Mechanical checks

• Power on and initial setup

Mechanical Checks

Before powering on the product, perform the following mechanical checks:

1. Confirm that all securing bolts are fully tightened and the appropriate mechanical locking washers are in

place.

2. Confirm all connections are secure.

3. Confirm all connecting cables and wires are secured and protected as necessary.

Power On the Control Head

See your Humminbird operations manual to configure the radar and start transmission.

Test the Installation

CHIRP_Radar_Install_Manual_532523-1EN_A.qxp_Layout 1 8/11/16 10:48 AM Page 22

Содержание CHIRP









































Результаты поиска

Содержание CHIRP

Отзывы:

Похожие инструкции для CHIRP

Бренды по названию

Популярные бренды

Humminbird CHIRP, Руководство по установке

Результаты поиска

Содержание CHIRP

Отзывы:

Похожие инструкции для CHIRP

Бренды по названию

Популярные бренды