Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

51

4.2.13 Low Ambient Humidity

This alarm is generated only for the power system that has a humidity sensor installed.

Possible Causes



The low ambient humidity alarm threshold is incorrectly set.



The humidity is too low in the cabinet where the humidity sensor is located.



The humidity sensor is faulty.

Measures

1.

Check whether the low humidity alarm threshold (10% RH by default) is correctly set. If
no, adjust it to a proper value.

2.

Check whether the humidity inside the cabinet is too low. If yes, adjust the humidity.
The alarm is cleared when the humidity returns to the allowed range.

3.

Check whether the humidity sensor is faulty. If yes, replace the humidity sensor.

4.2.14 Batt. High Temp.

This alarm is generated only for the power system that has a battery temperature sensor installed.

Possible Causes



The high battery temperature alarm threshold is incorrectly set.



The battery temperature control system is faulty.



The battery temperature sensor is faulty.

Measures

1.

Check whether the high battery temperature alarm threshold (50°C by default) is
correctly set. If not, set the threshold to the correct value.

2.

Check whether the battery temperature control system is faulty. If so, rectify the fault.
The alarm is cleared when the battery temperature falls within the allowed range.

3.

Check whether the battery temperature sensor is faulty. If so, replace the temperature
sensor.

4.2.15 Batt. Low Temp.

This alarm is generated only for the power system that has a battery temperature sensor installed.

Possible Causes



The low battery temperature alarm threshold is incorrectly set on the SMU.



The battery temperature control system is faulty.



The battery temperature sensor is faulty.

«
...
56
57
58
59
60
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренд: Rapid Страницы: 6

Бренд: SafetySpeed Страницы: 43

Бренд: Wayne Страницы: 8

Бренд: tacwise Страницы: 12

Бренд: SilverStone Страницы: 12

Бренд: SMC Networks Страницы: 2

Бренд: AP&T Страницы: 3

Бренд: Malibu Boats Страницы: 4

Бренд: Himax Страницы: 2

Бренд: Ryobi Страницы: 8

Бренд: Westfalia Страницы: 20

Бренд: Teccpo Страницы: 16

Бренд: Labgear Страницы: 3

Бренд: Happy Henhouse Страницы: 20

Бренд: RED ROOSTER Страницы: 8

Бренд: Timberline Tool Страницы: 6

Бренд: Parkside Страницы: 43

Бренд: Sealey Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды