Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

53

Measures

1.

Check whether there is smoke inside the cabinet. If so, disconnect the power supply from
the cabinet, handle the fault, and then restart the system and clear the alarm on the SMU.

2.

Check whether the smoke sensor is faulty. If the smoke sensor is faulty, replace it.

4.2.19 Rect Fault

Possible Causes



Rectifier connections are loose.



A rectifier is faulty.

Measures

1.

Check the Fault indicator on the rectifier panel. If it is steady red, remove the rectifier,
and then reinstall it after the indicator turns off.

2.

If the alarm persists, replace the rectifier.

4.2.20 Rect Protection

Possible Causes



The rectifier input voltage is too high.



The rectifier input voltage is too low.



The ambient temperature is too high.



The rectifier is abnormal.

Measures

1.

Check whether the AC input voltage exceeds the upper threshold for rectifier working
voltage. If so, locate and rectify the power supply fault and restore the power supply.

2.

Check whether the AC input voltage is below the lower threshold for rectifier working
voltage. If so, locate and rectify the power supply fault and restore the power supply.

3.

Check whether the ambient temperature is higher than the maximum operating
temperature of the rectifier. If so, locate and rectify the temperature control system fault.

4.

Remove the rectifier that has generated the alarm and reinstall it after the indicator turns
off. If the alarm persists, replace the rectifier.

4.2.21 Rect Comm Fault

Possible Causes



A rectifier has been removed.



Rectifier connections are loose.



A rectifier is faulty.

Measures

1.

Check whether a rectifier has been removed. If so, reinstall it.

2.

If the rectifier is in position, remove the rectifier and reinstall it.

«
...
58
59
60
61
62
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренд: U-Line Страницы: 15

Бренд: Earlex Страницы: 5

Бренд: K-Tool Страницы: 20

Бренд: Rapid Страницы: 8

Бренд: Parkside Страницы: 35

Бренд: ITech Страницы: 73

Бренд: V-TAC Страницы: 13

Бренд: Hantarex Страницы: 24

Бренд: Far Tools Страницы: 74

Бренд: Greatneck Страницы: 17

Бренд: Grizzly Страницы: 136

SecuriFire B6-PSU

Бренд: Securiton Страницы: 18

Бренд: Baileigh Industrial Страницы: 36

Бренд: Sealey Страницы: 4

Бренд: Laguna Tools Страницы: 50

FAST-Bi-1K5 Series

Бренд: Caen ELS Страницы: 55

Бренд: Hitachi Koki Страницы: 41

Бренд: Husqvarna Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды