Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

2 Overview

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

18

Item

TP48200A-HT19C3

TP48200A-HT19C4

(Optional) AC output circuit
breaker

One 2-pole 10 A circuit breaker and one 3-pole maintenance socket
protected by an 10 A electric residual current device (RCD).

DC output



Battery low voltage disconnection (BLVD): two 1-pole 10 A circuit
breakers and four 1-pole 16 A circuit breakers



Load low voltage disconnection (LLVD): one 1-pole 100 A circuit
breaker, one 1-pole 63 A circuit breaker, and four 1-pole 32 A circuit
breakers



Battery route: two 1-pole 125 A circuit breakers

Rectifier

A maximum of four R4850G2s or R4830G2s can be configured.

SMU

One SMU02B

UIM

One UIM02C

Sensor



Mandatory: one battery temperature sensor, one ambient temperature
sensor in the equipment compartment, and one door status sensor



Optional: one smoke sensor, one ambient temperature and humidity
sensor, and one water sensor.

(Optional) Intelligent electric meter One intelligent electric meter and one current transformer

(Optional) Bluetooth door lock

One electric door lock and one Bluetooth controller

Battery

The battery compartment with two layers supports a maximum of two 12
V, 150 Ah battery strings.

Maximum output power

12 kW

Class C environments refer to sea environments or outdoor land environments (with simple shielding
measures) near pollution sources. If a site is near a pollution source, it is at most 3.7 km away from salt
water, such as the sea and salt lakes, 3 km away from heavy pollution sources, such as smelteries, coal
mines, and thermal power plants, 2 km away from medium pollution sources, such as chemical, rubber,
and galvanization industries, and 1 km away from light pollution sources, such as packing houses,
tanneries, and boiler rooms.

«
...
23
24
25
26
27
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 48

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 15

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 4

Бренд: Makita Страницы: 9

Бренд: Hama Страницы: 24

Бренд: JBM Страницы: 12

Бренд: Ratio Electric Страницы: 4

EnergyGrind-100

Бренд: PEUGEOT Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды