Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

55

4.3.2 Identifying Circuit Breaker Faults

The following indicate that the circuit breaker is faulty:



The circuit breaker cannot be switched to ON/OFF after the short circuit fault for its end
circuit is rectified.



When the circuit breaker is switched to ON and its input voltage is normal, the voltage
between the two ends of the circuit breaker exceeds 1 V.



The input voltage is normal, but the resistance between both ends of the circuit breaker is
less than 1 kΩ when the circuit breaker is OFF.

4.3.3 Identifying Rectifier Faults

A rectifier is damaged if any of the following conditions is not met:



When the rectifier does not communicate with the SMU and the AC input voltage is
around 220 V, the green indicator on the rectifier is steady on and the other indicators are
off. The rectifier output is normal.



The SMU can perform equalized charging, float charging, and current limiting control
for the rectifier when the communication cable to the rectifier is correctly connected and
communication is established between the rectifier and the SMU.

4.3.4 Identifying SMU Faults

The following indicate that the SMU is faulty:



The DC output is normal but the green indicator on the SMU is off.



The SMU breaks down or cannot be started. Its LCD has abnormal display or buttons
cannot be operated.



With alarm reporting enabled, the SMU does not report alarms when the power system is
faulty.



The SMU reports an alarm when the power system is not faulty.



The SMU fails to communicate with the connected lower-level devices even though the
communications cables are correctly connected.



Communication between the SMU and all rectifiers fails even though the rectifiers and
the communications cables are normal.



The SMU cannot monitor AC or DC power distribution when communications cables are
intact and AC and DC power distribution is normal.



Parameters cannot be set or running information cannot be viewed on the SMU.

4.4 Replacing Components

«
...
60
61
62
63
64
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

BAE PS-XA-3Y-24-250-609-I

Бренд: Balluff Страницы: 48

Бренд: AccuMate Страницы: 12

Бренд: C-TEC Страницы: 2

Бренд: Panduit Страницы: 2

Бренд: Xantrex Страницы: 76

Бренд: Neumann.Berlin Страницы: 12

Бренд: Napa Страницы: 12

Бренд: Ingersoll-Rand Страницы: 23

Бренд: Proluxe Страницы: 17

Бренд: V-TAC Страницы: 13

Бренд: Parkside Страницы: 51

Бренд: Altronix Страницы: 8

Бренд: EINHELL Страницы: 34

Бренд: Altronix Страницы: 2

ABRASIVE UMB 4-RQ

Бренд: SUHNER Страницы: 36

Бренд: Novus Страницы: 22

Бренд: Yokota Страницы: 8

Бренд: Makita Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды