Huawei SUN2000-60KTL-M0 Скачать руководство пользователя страница 101

Страница: 101 / 127

Maintenance

8.1 Routine Maintenance

To ensure that the SUN2000 can operate properly for a long term, you are advised

to perform routine maintenance on it as described in this chapter.

CA UTION

●

Before cleaning the system and maintaining the cable connections and

grounding reliability, power off the system and ensure that the two DC

switches on the SUN2000 are OFF.

●

If you need to open the maintenance compartment door on rainy or snowy

days, take protective measures to prevent rain and snow entering the

maintenance compartment. If it is impossible to take protective measures, do

not open the maintenance compartment door on rainy or snowy days.

Table 8-1 Maintenance checklist

Item

Check Method

Maintenance

Frequency

System

cleanliness

Periodically check that the heat

sinks are free from obstacles or

dust.

Once every six to

twelve months

System running

status

● Check that the SUN2000 is not

damaged or deformed.

● Check that the running sound of

the SUN2000 is normal.

● When the SUN2000 is running,

check that all SUN2000

parameters are correctly set.

Once every six

months

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

8 Maintenance

Issue 06 (2020-10-12)

Содержание SUN2000-60KTL-M0
































































































































Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды

Huawei SUN2000-60KTL-M0, Руководство пользователя

Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды