Huawei SUN2000-60KTL-M0 Скачать руководство пользователя страница 110

Страница: 110 / 127

Alarm

Alarm Name

Alarm

Severity

Cause

Measures

2062

Low Insulation

Resistance

Major

Cause ID = 1
1. The PV string is short-

circuited to PE.

2. The PV string has been

in a moist environment

for a long time and the

power cable is not well

insulated to ground.

1. Check the impedance

between the PV string

and the PE cable. If a

short circuit occurs,

rectify the fault.

2. Check that the PE

cable for the

SUN2000 is correctly

connected.

3. If you are sure that

the impedance is less

than the default value

in a cloudy or rainy

environment, reset

Insulation resistance

protection.

2063

Cabinet

Overtemperatur

Minor

Cause ID = 1
1. The SUN2000 is

installed in a place with

poor ventilation.

2. The ambient

temperature exceeds

the upper threshold.

3. The SUN2000 is not

working properly.

1. Check the ventilation

and ambient

temperature at the

SUN2000 installation

position. If the

ventilation is poor or

the ambient

temperature exceeds

the upper threshold,

improve the

ventilation and heat

dissipation.

2. If the ventilation and

ambient temperature

both meet

requirements, contact

Huawei technical

support.

2064

Device Fault

Major

Cause ID = 1–15
An unrecoverable fault

occurs on a circuit inside

the SUN2000.

Turn off the AC output

switch and DC input

switch, and then turn

them on after 15

minutes. If the fault

persists, contact Huawei

technical support.

NOTE

Cause ID = 1: Perform the

preceding operations when

the PV string current is less

than 1 A.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

8 Maintenance

Issue 06 (2020-10-12)

103

Содержание SUN2000-60KTL-M0
































































































































Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды

Huawei SUN2000-60KTL-M0, Руководство пользователя

Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды