Huawei SUN2000-60KTL-M0 Скачать руководство пользователя страница 59

Страница: 59 / 127

●

If the MBUS (PLC) communication mode is selected, do not connect the

RS485 communications cable. In addition, you need to set MBUS

Communication to Enable on the SUN2000 app.

NO TICE

The MBUS (PLC) communication mode is only applicable to medium-voltage

grid connection scenarios and non-low-voltage public grid connection

scenarios (industrial environment).

●

If the RS485 communication mode is selected, do not connect the MBUS CCO

module to the AC power cable. In addition, you are advised to set MBUS

Communication to Disable on the SUN2000 app.

5.6.2 Installing the RS485 Communications Cable

Selecting an Installation Mode

An RS485 communications cable can be connected in two ways:
●

Terminal block connection
Recommended: Communications cable with a conductor cross-sectional area

of 1 mm

and a cable outer diameter of 14–18 mm.

●

RJ45 network port connection
Recommended: CAT 5E outdoor shielded network cable with an outer

diameter less than 9 mm and internal resistance no greater than 1.5 ohms/10

m, with a shielded RJ45 connector.

NO TE

Select only one installation mode in practice. Terminal block connection is

recommended.

NO TICE

When laying out communications cables, separate them from power cables to

avoid strong signal interference sources.

5.6.2.1 Terminal Block Connection

Terminal Block Port Definitions

Figure 5-21

shows an RS485 terminal block.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

5 Electrical Connections

Issue 06 (2020-10-12)

Содержание SUN2000-60KTL-M0
































































































































Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды

Huawei SUN2000-60KTL-M0, Руководство пользователя

Результаты поиска

Содержание SUN2000-60KTL-M0

Отзывы:

Похожие инструкции для SUN2000-60KTL-M0

Бренды по названию

Популярные бренды