Huawei SUN2000-55KTL Скачать руководство пользователя страница 109

Страница: 109 / 122

SUN2000-(55KTL, 60KTL) Series
User Manual

8 System Maintenance

Issue 06 (2020-01-03)

103

Alarm ID Alarm

Name

Alarm
Severity

Possible Cause

Suggestion

410

Abnormal
Auxiliary
Power

Major

Cause ID = 4

The sampling control board has
an abnormal voltage, which
may be caused by the
following:



The internal power chip of
the sampling control board
is faulty.



The detection circuit
becomes faulty.

When the alarm is generated, the
inverter shuts down
automatically. When the fault is
rectified, the inverter starts
automatically.

If the alarm persists, contact
Huawei technical support.

413

Abnormal
PV String
Connectio
n

Major

Cause ID = 1

The PV string does not
properly connect to the MPPT1
circuit.

Cause ID = 2

The PV string does not
properly connect to the MPPT2
circuit.

Cause ID = 3

The PV string does not
properly connect to the MPPT3
circuit.

Cause ID = 4

The PV string does not
properly connect to the MPPT4
circuit.

Check the PV string for reverse
connection and cross connection.

504

Software
Version
Unmatch

Minor

Cause ID = 1/2/3

During inverter software
upgrade, the version of the
software loaded is incorrect.

Check whether you have performed a
software upgrade recently. If yes,
upgrade the software to the correct
version again.

505

Upgrade
Failed

Major

Cause ID = 1

The upgrade does not end
normally.

Perform the upgrade again.

61440

Flash
Fault

Minor

Cause ID = 1



The flash memory is
insufficient.



The flash memory has bad
sectors.

Replace the monitoring board.

If the monitoring board is built
into the monitoring device,
replace the monitoring device.

If you cannot rectify faults with the measures listed in the preceding table, contact Huawei technical
support.

Содержание SUN2000-55KTL



























































































































Результаты поиска

Содержание SUN2000-55KTL

Отзывы:

Похожие инструкции для SUN2000-55KTL

Бренды по названию

Популярные бренды

Huawei SUN2000-55KTL, Руководство пользователя

Результаты поиска

Содержание SUN2000-55KTL

Отзывы:

Похожие инструкции для SUN2000-55KTL

Бренды по названию

Популярные бренды