Huawei S3026C-PWR Скачать руководство пользователя страница 61

Страница: 61 / 80

Installation Manual
Quidway S3026C-PWR Ethernet Switch

Chapter 7 Optional Modules

Caution:

When connecting the fiber optic, pay attention to the following:

Do not bend the fiber optic overly.

Correctly connect the transmit end and the receive end of the module interface.

Keep the optical interface clean.

7.3 Single-port 1000Base-ZX Long-haul Module

1000Base-ZX long-haul module provides one Gigabit optical port and matches

single mode fiber with a maximum transmission distance of 70km.

7.3.1 Panel and LEDs

1000Base-ZX module supported on S3026C-PWR has a panel as shown in the

following figure.

Figure 7-3

1000Base-ZX module panel

The following table summarizes the LEDs on the panel.

Table 7-3

LEDs on 1000Base-ZX module

LED Status

OFF

The link is down.

LNK

The link is up.

OFF

No packets are being transmitted/received.

ACT

Flashing

Packets are being transmitted/received.

7.3.2 Port Fiber

1000Base-ZX module matches LC connector.

Huawei Technologies Proprietary

7-4

Содержание S3026C-PWR

















































































Результаты поиска

Содержание S3026C-PWR

Отзывы:

Бренды по названию

Популярные бренды

Huawei S3026C-PWR, Руководство по установке

Результаты поиска

Содержание S3026C-PWR

Отзывы:

Бренды по названию

Популярные бренды