Huawei NetCol5000-A011 Скачать руководство пользователя страница 25

Страница: 25 / 28

If the R410A refrigerant is provided by Huawei, put the refrigerant cylinder upside down when

charging in the refrigerant. If the refrigerant is not provided by Huawei, check with the refrigerant

provider whether the cylinder has a siphon. If the cylinder has a siphon, stand the cylinder when

charging in refrigerant. If the cylinder has no siphon, put the cylinder upside down when charging

in refrigerant. These measures ensure that the refrigerant is charged in the liquid state.

Outdoor Ambient Temperature

Proper Discharge Pressure Range

Below 15

1.5–2.5 MPa

15–35

1.5–3.1 MPa

35–45

2.5–3.8 MPa

Above 45

3.1–4.0 MPa



On the

Diagnostic Mode Parameters

page, set

Comp manual control

to 3000 rpm.



Choose

Running Info

Compressor Information

and view the

Suction pressure

and

Discharge pressure

to determine whether they are within normal ranges. The normal suction

pressure range is 0.7–1.6 MPa, and the ratio (air discharge pressure/air suction pressure) > 1.4.

The normal discharge pressure range is listed in the following table. Check the

EEV suction

overheating degree

(normal range: 4–15

C) on the

Running Info

Electronic Expansion

Valve Information

page.

a. Close the high-pressure valve and low-pressure valve of the pressure gauge.

b. Take off the vacuum pump from the vacuumizing equipment, and replace the vacuum

pump with a refrigerant cylinder.

c. Slightly open the refrigerant cylinder valve and slightly loosen the connection nut on the

leather hose. Tighten the nut when cold air escapes out of the nut.

d. Put the refrigerant cylinder upside down on an electric balance. Set the reading on the

balance to zero.

e. Start the compressor and let it run for 10 minutes.

f. Open the low-pressure valve and refrigerant steel cylinder valve at the joint of the gas

pipe needle valve, and then charge refrigerant at the gas pipe needle valve.

g. Charge liquid refrigerant.

h. After the refrigerant is charged, close all pressure gauge valves and the refrigerant

cylinder valve.

i. Remove the refrigerant charging device and install the bonnet.

Содержание NetCol5000-A011





























Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды

Huawei NetCol5000-A011, Быстрое руководство

Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды