Huawei NetCol5000-A011 Скачать руководство пользователя страница 24

Страница: 24 / 28

1. Log in to the WebUI of the ECC controller as an administrator and choose

Monitoring

Air

Conditioner > NetCol5000-A0101

to enter the settings page.

2. Click

Controls

Control Information

, choose

On/off status on EMS

, and then click

Submit

3. On the

Controls

Control Information

page, choose

Diagnostic Mode

Enable

and click

Submit

4. Choose

Running Parameters

Diagnostic Mode Parameters,

on the

Diagnostic Mode

Parameters

page, set

EEV Opening

of the electronic expansion valve to

300step

, set

Liquid

Solenoid Val t

Open

and click

Submit

, then keep that for 30s to allow for the positive

pressure inside the refrigerant pipe of the indoor unit.

5. (Optional) Choose

Running Parameters

Diagnostic Mode Parameters

. Then choose

Elec

heater manual control

Open

and click

Submit



Check that the indoor fan operates properly without alarms.



If hot air blows out from the air exhaust vent of the fan after a period of time, the electric

heater runs properly. In this case, choose

Elec heater manual control

Closed

and then

click

Submit

6. (Optional) Commission the wet film humidifier.



On the

Diagnostic Mode Parameters

page, set

Inlet solenoid man ctrl

Open

and

click

Submit

. Check that the water inlet pipe does not leak and the humidifier float works

properly. Choose

Inlet solenoid man ctrl

Closed

and then click

Submit



Choose

Humidifier film man ctrl

Open

and click

Submit

. Then choose

Running Info

Humidifier Information

Humidifier pump ctrl

and check that the humidifier water

pump is open and water flows down along the wet film. Choose

Humidifier film man

ctrl

Closed

and then click

Submit

7. Commission the condensate pump. Lift the low liquid level detector. After 5 seconds, when

you hear the water pump operating sound, lay down the low liquid level detector. (It is

normal if a pump alarm is generated when there is no water in the pan. The pump generates

this alarm for self-protection and this alarm needs to be cleared manually.)

8. Commission the compressor. If required charge refrigerant, perform the following steps.

Содержание NetCol5000-A011





























Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды

Huawei NetCol5000-A011, Быстрое руководство

Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды