Huawei NetCol5000-A011 Скачать руководство пользователя страница 19

Страница: 19 / 28

No. Cable Name

From

Electric heater contactor

cable (required if an electric

heater is configured)

Converged cabinet XT4-6 and XT4-

5 correspond to smart cooling

products 1 and 2, respectively. The

third smart cooling product is not

configured with this cable by

default.

Contactor KM1 of the

corresponding smart cooling

product

The third smart cooling

product is not configured

with this cable by default.

2 Control unit input power

cable

Converged cabinet XT4-4

INPUT1 port on the control

unit

3 Outdoor unit power cable (3

x 6 mm

)

L (converged cabinet XT4-1, XT4-2,

and XT4-3 correspond to outdoor

units 3, 2, and 1, respectively.), N

bar, PE bar

L, N, and ground ports on

the electric control box of

the outdoor unit

Signal cable for the indoor

and outdoor units (3 cores

outdoor shielded cable, 16-22

AWG)

X2.1, X2.2, and X2.3 ports on the

indoor unit

P, Q, and E ports on the

electric control box of the

outdoor unit

5 J1 cable

X101, X102, and X103 ports on the

indoor unit

J1 port on the control unit

6 J2 cable

X101, X102, and X103 ports on the

indoor unit

J2 port on the control unit

7 Control unit output power

cable

X1.1, X1.2, X1.3, and FU1-FU3 ports

on the indoor unit

OUT1 port on the control

unit

8 J3 cable

X101, X102, and X103 ports on the

indoor unit

J3 port on the control unit

9 J4 cable

X101, X102, and X103 ports on the

indoor unit

J4 port on the control unit

10 Temperature/Humidity (T/H)

sensor cable

RS485/12V port on the control unit T/H sensor

11 ECC800 cable

FE-2 port on the control unit

•

If the smart ETH gateway

is configured, connect the

cable to the PoE port on

the smart ETH gateway.

•

If no smart ETH gateway

is configured, connect the

cable to the WAN_2 port

on the ECC800.

12 Ground cable

Ground point on the control unit

IT cabinet ground copper

bar

Verifying the Installation

•

Do not pull cables J1, J2, J3, and J4 and their terminals casually. Ensure that the cables

are connected securely.

•

If there are only two smart cooling products in the converged cabinet, you only have to

connect cables 3, 4, and 10, since other cables are factory-installed. If there are three

smart cooling products, all cables except 1 to the third smart cooling product have to

be connected onsite.

•

The length of signal cable for the indoor and outdoor units cannot exceed 200 meters.

•

The signal cable should be shielded, and the shield layer shall be grounded.

Содержание NetCol5000-A011





























Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды

Huawei NetCol5000-A011, Быстрое руководство

Результаты поиска

Содержание NetCol5000-A011

Отзывы:

Похожие инструкции для NetCol5000-A011

Бренды по названию

Популярные бренды