Huawei LUNA2000-30-S0 Скачать руководство пользователя

Страница: 47 / 129

WARNING

In the off-grid state, the output phases of cascaded inverters are different. The

load outputs of the Backup Boxes connected to each inverters cannot be

connected in parallel. As shown in the following figure, the P-1 output is

connected to primary O-1 and the P-2 output is connected to O-2. The P-1 and

P-2 load outputs cannot be connected in parallel.

Smart Dongle Networking

A maximum of three inverters can be cascaded in the grid-tied and off-grid ESS.

The batteries, power meter, Smart Dongle, and Backup Box need to be connected

to the same inverter.

Figure 3-14 Smart Dongle networking in a grid-tied and off-grid ESS (dashed

boxes indicate optional components)

LUNA2000-(5-30)-S0

User Manual

3 Application Scenarios and Settings

Issue 07 (2022-01-10)

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды

Huawei LUNA2000-30-S0, Руководство пользователя

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды