Huawei LUNA2000-30-S0 Скачать руководство пользователя страница 45

Страница: 45 / 129

Cascading

Mode

SUN2000

SmartLogger

SUN2000-

(3KTL-10KTL)-M1
(with batteries)

SUN2000-(3KTL-10KTL)-

M1
(with batteries)

SUN2000-(20KTL, 29.9KTL,

30KTL, 36KTL, 40KTL)-M3

SmartLogger

SUN2000-

(3KTL-10KTL)-M1
(with batteries)

SUN2000-(3KTL-10KTL)-

M1
(with batteries)

SUN2000-(8KTL-20KTL)-M2

SmartLogger

SUN2000-

(3KTL-10KTL)-M1
(with batteries)

SUN2000-(3KTL-10KTL)-

M1
(with batteries)

SUN2000-(3KTL-10KTL)-M1
(with batteries)

The grid-tied and off-grid ESS supports a maximum of three SUN2000-

(2KTL-6KTL)-L1 inverters (with batteries) cascaded. In this scenario, the inverters

can be connected to the grid only at the same phase and controlled only by a

single-phase power meter. Grid connection at different phases or using a three-

phase power meter is not supported.

LUNA2000-(5-30)-S0

User Manual

3 Application Scenarios and Settings

Issue 07 (2022-01-10)

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Huawei LUNA2000-30-S0, Руководство пользователя, Страница: 45 / 129

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы: