Huawei FusionModule500 Скачать руководство пользователя страница 90

Страница: 90 / 302

●

At a high place with strong winds, install the outdoor unit against a wall to

ensure the normal operating of fans. Install a baffle plate when necessary to

prevent the outdoor unit from toppling in strong winds.

●

Install an outdoor unit against a wall if possible. If the site conditions cannot

meet the requirements and the local outdoor temperature may be below –

10°C, install a baffle plate by referring to the space requirements. The baffle

plate height and width should be greater than or equal to the outdoor unit

height and width, respectively.

●

If the site installation environment is complicated and the preceding

conditions are not met, contact Huawei technical support.

Space Requirements

Figure 4-18 Space requirements

4.2.4.5.2 Securing an Outdoor Unit

Prerequisites

●

The M10 expansion bolts used for securing an outdoor unit have been

prepared.

●

The concrete groundwork is prepared.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

Содержание FusionModule500















































































































































































































































































































Результаты поиска

Содержание FusionModule500

Отзывы:

Бренды по названию

Популярные бренды

Huawei FusionModule500, Руководство пользователя

Результаты поиска

Содержание FusionModule500

Отзывы:

Бренды по названию

Популярные бренды