Huawei FusionModule500 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 302

background image

Item

Specifications

LAN port

● Supports two LAN ports, which can be connected to the

LAN. The ports support autonegotiation of 10/100/1000

Mbit/s communication rates.

● Connect shielded network cables to the LAN ports.

RS485 serial

port

expansion

● Output voltage: 13–15 V DC (rated voltage: 14.5 V DC)
● Four RS485 ports with the default communications rate of

9600 bit/s

● COM1–COM3 ports provide 12 V DC power.
● The power supply can be switched on or off and is on by

default.

PoE expansion Supports two PoE (GE) ports for expansion of the PoE bus, and

supports network isolation and ring network.

AIDI

expansion

(RJ45)

● Output voltage: 13–15 V DC (rated voltage: 14.5 V DC)
● Provides five universal AIDI ports for connecting to sensors

such as smoke sensors, water sensors, and NTC sensors.

AIDI_1 to AIDI_3 are full-function AIDI ports, and AIDI_4 to

AIDI_5 are simplified AIDI ports without type identification.

● The power supply can be switched on or off and is on by

default.

DO expansion

(RJ45)

● Output voltage: 13–15 V DC (rated voltage: 14.5 V DC)
● Supports one active DO port.
● The power supply can be switched on or off and is on by

default.

Fault isolation There are three groups of 12 V ports. A group has a maximum

current of 660 mA, a route has a maximum current of 800 mA,

and the maximum total current is 2 A.
Group 1: 12 V of the AIDI_1 and DO/12V ports
Group 2: 12 V of the AIDI_2, COM1/AIDI_4, and COM3/12V

ports
Group 3: 12 V of the AIDI_3 and COM2/AIDI_5 ports

Wireless

communicatio

n

Supports wireless communication that complies with

IEEE802.15.4.

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

33

«
...
41
42
43
44
45
...
»

Содержание FusionModule500















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule500

LM Pro 63 Series

Бренд: G-Tek Страницы: 40

Бренд: G-Tek Страницы: 25

Бренд: ACR Systems Страницы: 24

Бренд: Spectrum Страницы: 12

Бренд: Racelogic Страницы: 49

Бренд: banks Страницы: 16

Бренд: Hantek Страницы: 36

Бренд: Omega Страницы: 12

UltraShock Series

Бренд: MadgeTech Страницы: 2

Бренд: MadgeTech Страницы: 2

Бренд: MadgeTech Страницы: 2

Бренд: MadgeTech Страницы: 2

Бренд: American Thermal Instruments Страницы: 10

Бренд: TECHNOLOG Страницы: 43

Бренд: InTemp Страницы: 6

Бренд: TempSen Страницы: 23

Бренд: Edelbrock Страницы: 40

Бренд: PEL Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды