Huawei FusionModule500 Скачать руководство пользователя страница 247

Страница: 247 / 302

Maintenance

Area

Maintenance

Item

Operation

Expected Result Troubleshootin

Indicator

The indicator on

the power

module is steady

green.

Check the

output voltage

and determine

whether the

power module

is faulty. If the

power module

is faulty, replace

it.

Fan

No abnormal

noise is

generated.

If abnormal

noise is

generated, clean

the fan.

Operating

environment

● Ambient

temperature:

–20°C to

+65°C

● Humidity:

0%–95% RH

(non-

condensing)

If the

temperature or

humidity is

abnormal, check

the smart

cooling product

status.

Monitoring

module indicator

The monitoring

module indicator

is steady green

or blinking

green.

If the indicator

is off or any

abnormal

condition

occurs, see

to rectify the

fault.

Network interface

indicator

The green

indicator is

steady on, and

the yellow

indicator is

blinking.

If the indicator

status is

abnormal, check

the network

cable

connection.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

237

Содержание FusionModule500















































































































































































































































































































Результаты поиска

Содержание FusionModule500

Отзывы:

Похожие инструкции для FusionModule500

Бренды по названию

Популярные бренды

Huawei FusionModule500, Руководство пользователя

Результаты поиска

Содержание FusionModule500

Отзывы:

Похожие инструкции для FusionModule500

Бренды по названию

Популярные бренды