Huawei FusionModule500 Скачать руководство пользователя страница 65

Страница: 65 / 302

Table 3-41 LAN switch

Model

Maximum Number of Ports

S5331-H24P4XC

Twenty-four 10/100/1000BASE-T Ethernet ports, four

10GE SFP+ ports

S5731-H24P4XC

Twenty-four 10/100/1000BASE-T Ethernet ports, four

10GE SFP+ ports

3.5 Surge Protection and Grounding System

3.5.1 Surge Protection Solution

The Smart Module is mainly used for building equipment rooms. Its power

distribution system is a subsystem of the building power distribution system. Class

I surge protective devices (SPDs) of the power system are provided by the general

low-voltage power distribution room or cabinet of the building.

3.5.2 Grounding Solution

Cabinet Potential Grounding

A general ground bar is installed in the cabinet. Ground terminals of the cabinet

are connected to the ground bar using a ground cable with a minimum cross-

sectional area of 16 mm

NO TE

The AC input power is from the upstream power distribution system. The cross-sectional

areas of ground cables are determined according to IEC 60364-5-54.

Cabinet Grounding

●

Metal components and parts of cabinets are properly connected. A structural

connection area is protected and applied with antioxidants. An area protected

with painting should ensure proper metal surface contact for two connected

components. The DC resistance is within 0.1 ohm between any two connected

metal components. Use a ground cable to connect two metal components

that cannot be directly connected, such as cabinets and cabinet doors. A cable

for connecting these two metal components has a minimum cross-sectional

area of 6 mm

●

A ground bar or general ground point is provided in the cabinet for

equipment grounding. The ground bar does not need to be insulated.

●

A ground terminal is greater than or equal to M8 in dimensions. A yellow

ground label

is attached close to the general ground terminal for

cabinets.

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Содержание FusionModule500















































































































































































































































































































Результаты поиска

Содержание FusionModule500

Отзывы:

Похожие инструкции для FusionModule500

Бренды по названию

Популярные бренды

Huawei FusionModule500, Руководство пользователя

Результаты поиска

Содержание FusionModule500

Отзывы:

Похожие инструкции для FusionModule500

Бренды по названию

Популярные бренды