Huawei FusionModule500 Скачать руководство пользователя страница 136

Страница: 136 / 302

Phillips screwdriver to fix the M6 screws on the mounting ears. Each mounting ear

uses two M6 screws.

Figure 4-81 Installing the device

----End

4.2.6.11 (Optional) Installing an IVS1800

Context

By default, the IVS1800 is delivered without disks. After the IVS1800 is delivered to

the site, install hard disks as required and then install the IVS1800 in the cabinet.

Procedure

Step 1 Install hard disks.

1. Use a PH2 screwdriver to remove the two black screws on the rear of the

chassis cover, and take off the chassis cover.

Figure 4-82 Removing the chassis cover

2. Remove two black screws on each side of the chassis and the silvery white

one on top of the hard disk tray, raise the hard disk tray by 45 degrees, and

take out the upper and then lower layers of hard disk tray.

Figure 4-83 Removing the hard disk tray

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

126

Содержание FusionModule500















































































































































































































































































































Результаты поиска

Содержание FusionModule500

Отзывы:

Бренды по названию

Популярные бренды

Huawei FusionModule500, Руководство пользователя

Результаты поиска

Содержание FusionModule500

Отзывы:

Бренды по названию

Популярные бренды