Huawei FusionDC1000A Скачать руководство пользователя страница 35

Страница: 35 / 130

Name

Model/Function

Quantity

Bolt for

securing the

ground

copper bar

M12x30 stainless steel bolt assembly

Configure 1

PCS for each

ground point.

Heat shrink

tubing

● Diameter: 50 mm; radial shrinkage: 50%;

operating temperature range: 55°C to 105°C

● Connects mains input power cables.

Colors subject

to local

regulations,

10 m long for

each

SIM card

The SIM card is installed in a card slot in the

ECC800-Pro main control module. The SIM card

must support GSM and WCDMA.

1 PCS

MicroSD

card

The microSD card is installed in a card slot in the

ECC800-Pro main control module. The capacity

ranges from 16 GB to 128 GB. The recommended

capacity is 32 GB.

1 PCS

NO TE

● This table may not list some tools required at specific sites. Onsite installation personnel

and technical support personnel should prepare tools based on site requirements.

● Some dedicated tools and installation materials provided with the equipment may not

be listed in this table.

● Preventive measures should be applied before installation to avoid water seepage into

pre-fab. modules and equipment in the case of a sudden change in the weather.

3.2 Installation Personnel Requirements

●

Installation personnel must be trained and qualified by Huawei to master

methods for system installation, and must obtain work permits before they

begin to install the equipment.

●

Technical personnel from the customer must be trained by Huawei and

master the installation method.

●

The number of construction personnel depends on the project progress and

installation environment.

●

Construction personnel have read through the safety precautions and related

product documents before they begin working.

NO TE

● Common technician: familiar with the equipment installation process.
● Skilled technician: familiar with the equipment installation process and having an electrician

certificate.

FusionDC1000A Prefabricated All-in-One Data

Center

Installation Guide (IT Scenario)

3 Installation Preparations

Issue 01 (2021-04-20)

Содержание FusionDC1000A



































































































































Результаты поиска

Содержание FusionDC1000A

Отзывы:

Похожие инструкции для FusionDC1000A

Бренды по названию

Популярные бренды

Huawei FusionDC1000A, Руководство по установке

Результаты поиска

Содержание FusionDC1000A

Отзывы:

Похожие инструкции для FusionDC1000A

Бренды по названию

Популярные бренды