Huawei FusionDC1000A Скачать руководство пользователя страница 119

Страница: 119 / 130

Figure A-5 DPJ end connector

(1) Body

(2) Ferrule

(3) Guarding

(4) Cover lock nut

(5) Plastic-coated metal hose

Preparations

Tools: small cutter, scissors, wrench dedicated for feeder windows, glue gun

Material: sealant

Skill requirement: skilled technician

Procedure

Step 1 Cut the plastic-coated metal hose to facilitate connection between the metal hose

and the ferrule.
1. Use a small cutter or a pair of scissors to cut the hose at the joint between

the plastic-coated metal hose and the end connector at an angle of 30 to 45

degrees.

Figure A-6 Cutting a hose

2. Trim any burrs on the cut.

Step 2 Remove the sealant from the DPJ end connector.

Step 3 Remove the cover lock nut, guarding, and ferrule from the DPJ end connector

using the feeder window wrench shipped with pre-fab. modules.

Step 4 Place the cover lock nut and guarding along a cable into the plastic-coated metal

hose.

FusionDC1000A Prefabricated All-in-One Data

Center

Installation Guide (IT Scenario)

A Basic Installation Operations

Issue 01 (2021-04-20)

112

Содержание FusionDC1000A



































































































































Результаты поиска

Содержание FusionDC1000A

Отзывы:

Похожие инструкции для FusionDC1000A

Бренды по названию

Популярные бренды

Huawei FusionDC1000A, Руководство по установке

Результаты поиска

Содержание FusionDC1000A

Отзывы:

Похожие инструкции для FusionDC1000A

Бренды по названию

Популярные бренды