Huawei BTS3900 V100R003 Скачать руководство пользователя страница 143

Страница: 143 / 264

–

Performs digital-to-analog conversion and IQ modulation

–

Performs orthogonal up-conversion of IF signals to the TX band

The power amplifier amplifies the low-power RF signals from the signal processing unit.

The duplexer has the following functions:

Multiplexes the RX signals and TX signals

Enables RX signals and TX signals to share one antenna channel

Filters RX signals and TX signals

LEDs

Table 4-50

describes the LEDs on the WRFU panel.

Table 4-50

LEDs on the MRFU panel

Label

Color

State

Description

RUN

Green

The power input is normal, but the
module is faulty.

OFF

There is no power input, or the module
is faulty.

ON for 1s and OFF for
1s

The module runs properly.

ON for 0.125s and OFF
for 0.125s

The module is loading software or is
not started.

ALM

Red

An alarm is generated, and the module
needs to be replaced.

Blinking (ON for 1s and
OFF for 1s)

An alarm is generated. The alarm may
be caused by the fault of the related
module or port. Therefore, whether the
module needs to be replaced cannot be
determined.

OFF

No alarm is generated.

ACT

Green

The module works properly (the TX
channel is set to ON).

ON for 1s and OFF for
1s

The module is running (the TX
channel is set to OFF).

VSWR

Red

ON (red)

A VSWR-related alarm is generated at
the ANT_TX/RXA port.

Blinking (ON for 1s and
OFF for 1s)

A VSWR-related alarm is generated at
the ANT_RXB port.

Blinking (ON for
0.125s and OFF for
0.125s)

A VSWR-related alarm is generated at
the ANT_TX/RXA and ANT_RXB
ports.

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-51

Содержание BTS3900 V100R003









































































































































































































































































Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды

Huawei BTS3900 V100R003, Описание аппаратуры

Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды